A Servo motor driven one-component positive rod displacement meter system for dispensing precise beads of medium to high viscosity mastic materials.

Designed for high speed robotic and automation production applications, requiring robot interface, variable flow rates, precision beads, low maintenance and long life.

Many rod sizes and dispense valves are available to meet the exact application requirements.

The Servo-Flo™ 305 system is a mid-sized shot meter ideal for robotic and automated dispensing applications such as bonding, gasketing, filling and sealing operations.

The Servo-Flo™ 305 can be floor, pedestal or robotic mounted for automation or manual applications.

System design selections include meter volume size, material temperature control, operator interface, dispense valve, material supply and system integration.

These Micro-Meter^® 1 series positive rod displacement meters dispenses single and multiple beads or specific shot sizes. The Servo-Shot Micro-Meters dispense precision volumes of 1-component materials in the range of 0.01 cc’s up to 3.6 cc’s. The Servo-Flo 401 meter dispenses precision volumes of 1-component materials in the range of 1 cc up to 8.5 cc’s.

The servo drive design allows the flow rate to be adjusted during the dispense cycle to ensure the bead profile or shot volume meets the application requirement.

The dispense valve can be meter outlet mounted or remote mounted for flexible location requirements.

MICROSHOT^™ 1

Dispenses 0.01cc and larger precise volumetric shots of one-component materials.

Air powered or Servo powered, rod displacement meter package for low or medium viscosity materials.

The meter can be supplied by cartridges, pressure tanks or supply pumps.

This one-component rod displacement metering system dispenses precise beads of low, medium or high viscosity materials.

Powered by an Air-Draulic^™ air-oil cylinder or Electric servo-motor drive system to provide pre-set consistent flow rates (air-oil) or variable flow rates (servo) for bead or spray applications.

The positive rod displacement metering unit is sized to your specific application requirement and available in sizes from small shots down to 1 cc and large volume shots up to 235 cc or larger.

This one-component rod displacement shot meter system dispenses precise shot volumes of low, medium or high viscosity materials. The meter uses adjustable position ‘hard stop’™ shot controls and clean cut-off dispense valves to dispense the exact volume.

The dispensed volume, from 1cc through several hundred cc’s, is adjusted manually and is powered by an air cylinder. The meter can be supplied by pressure tanks or pumps.

The controls allow integration with automation for precision volumes of material dispensed on demand.

Various shot meter sizes available to meet your application requirements.

The ISD meter is double-acting for continuous flow of 1-component medium to high viscosity materials. This system is ideal for sealer dispensing applications requiring high volumes dispensed quickly without reloading.

ISD systems typically use 2-ball or chop-check high volume pumps. Select a dispensing valve from a wide selection including Servo-Ribbon Applicator, Multi-Stream Applicator, Slotted Nozzle Applicator, Snuf-Bak, Tip-Seal and No-Drip for extruding, streaming and spraying materials.

Meter options include waterborne/abrasive material design, DeviceNet and material temperature control.

IPD - INTEGRATED PNEUMATIC DISPENSER

This high volume, air powered, positive rod displacement meter system dispenses an accurate fluid pressure of medium to high viscosity 1-component materials.

The IPD meter is ideal for spray applications requiring large volumes of material applied quickly at specific pressure. The Dual IPD system provides uninterrupted continuous flow for any volume required.

Meter options include waterborne/abrasive material design, DeviceNet and material temperature control. Select from a variety of dispense valves.

IPS - INTEGRATED PNEUMATIC SYSTEM

This high volume, air powered, positive rod displacement meter system dispenses an accurate flow rate of medium to high viscosity 1-component materials such as mastics, deadeners and reinforcement materials.

The IPS meter is ideal for applications requiring large volumes of material applied quickly at a specific flow rate for volume control. The Dual IPS system provides uninterrupted continuous flow for any volume required.

Meter options include waterborne/abrasive material design, DeviceNet and material temperature control. Select from a variety of dispense valves.

The Servo-Flo™ 502 is a positive-displacement, single-component, single-acting shot meter designed to produce a controlled flow of 1-component materials.

Each meter is appropriately sized to provide the capacity requirements of individual applications, within the constraints of the design.

The Servo-Flo 502 is supplied by high volume pumps and precisely meters the material to the selected dispense valve.

SERVO-FLO™ GEAR METER

The Servo-Flo Gear Meter is a servo motor driven pump specifically designed for precision metering of medium to high viscosity materials.

This meter is typically used for dispensing 1-Component silicones and urethanes for gasketing applications.

The Servo-Flo Gear Meters do not require reloading at the end of the dispense cycle and allow the flow rate to adjust during dispense and from part to part.

This meter can be combined with a second gear meter for 2-Component meter-mix and dispense.